meta data for this page
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
drives:pc525 [2022/02/11 20:05] – [5.25" PC Floppy Drives] Added generic instructions flan | drives:pc525 [2023/01/18 09:17] (current) – Added Panasonic JU-475 flan | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== 5.25" PC Floppy Drives ====== | ====== 5.25" PC Floppy Drives ====== | ||
- | The Applesauce works with most PC floppy drives, but requires the [[https:// | + | The Applesauce |
⚠️ The cable has two connectors, but **only connect one drive at a time**! | ⚠️ The cable has two connectors, but **only connect one drive at a time**! | ||
Line 7: | Line 7: | ||
Drives can be configured to be either Drive 1 or Drive 2—the Applesauce will try both. The drive should also be configured for a **non-twisted** cable. | Drives can be configured to be either Drive 1 or Drive 2—the Applesauce will try both. The drive should also be configured for a **non-twisted** cable. | ||
- | Most PC drives work at 300 RPM for low-density disks and/or 360 RPM for high-density disks. If the drive supports both, it is best to allow the Applesauce to control the speed. This way the client software can analyze the flux timings to figure out at which speed the disk was written, then switch to the correct speed for imaging. | + | If the drive supports both low-density disks (300 RPM) and high-density disks (360 RPM), then it best to allow the Applesauce to control the speed. This way the client software can analyze the flux timings to figure out at which speed the disk was written, then switch to the correct speed for imaging. |
⚠️ **Always update the Drive Configuration after changing jumpers!** | ⚠️ **Always update the Drive Configuration after changing jumpers!** | ||
+ | ---- | ||
+ | |||
+ | ===== EPSON ===== | ||
+ | |||
+ | ==== SD-700 ==== | ||
+ | |||
+ | ^ Step time | ||
+ | ^ Settle time | 15 ms | | ||
+ | ^ Jumpers | ||
+ | |||
+ | [[drives: | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ===== Panasonic ===== | ||
+ | |||
+ | ==== JU-475 ==== | ||
+ | |||
+ | ^ Step time | ||
+ | ^ Settle time | 15 ms | | ||
+ | ^ Jumpers | ||
+ | |||
+ | [[drives: | ||
+ | |||
+ | ---- | ||
===== NEC ===== | ===== NEC ===== | ||
Line 20: | Line 45: | ||
[[drives: | [[drives: | ||
+ | |||
+ | ---- | ||
===== TEAC ===== | ===== TEAC ===== | ||
Line 28: | Line 55: | ||
^ Model ^ Jumpers | ^ Model ^ Jumpers | ||
+ | | 149-U | RY, D1, I | {{ : | ||
+ | | 193-U | RY, D1, I | {{ : | ||
| 7193-U | RY, D1, I | {{ gallery: | | 7193-U | RY, D1, I | {{ gallery: | ||
+ | |||
+ | |||
+ | ==== FD55-GFV ==== | ||
+ | |||
+ | ^ Step time | ||
+ | ^ Settle time | 15 ms | | ||
+ | ^ Jumpers | ||
+ | |||
+ | [[drives: | ||
+ | |||
+ | ---- | ||